>
Coaxial Resonator Eigenmode Analysis in HFSS
Jun 6, 2025 - Hi there! This video shows how to use the Eigenmode solver in Ansys HFSS by analyzing a silver-plated coaxial resonator. The example highlights how the solver computes both the res...
>
Digital Twin: Battery Module Simulation with Linear Time Invariant Reduced Order Model
Jun 5, 2025 - This video provides a setup of a Digital Twin simulation using Ansys Fluent and Ansys Twin Builder. It showcases Digital Twin’s capability to quickly simulate battery module cel...
>
1D Parametric Analysis of a Centrifugal Pump
Jun 5, 2025 - In this video we use one part of the Ansys TurboTools to perform a one-dimensional analysis of a radial pump.
>
Enabling Additional CPU Cores and GPU in Ansys Electronics Desktop
May 30, 2025 - Hi there! This video shows how to enable additional CPU cores and GPU in Ansys Electronics Desktop.
Please check out our blog: https://blog.ozeninc.com/resources/enabling-addition...
>
On-the-Fly Design and Analysis using Ansys Discovery
May 30, 2025 - This video shows how to make on-the-fly design changes on a HVAC duct system to optimize flow distribution.
Please check out our blog: (https://blog.ozeninc.com/resources/on-the-fl...
>
Capacitance Extraction Using Ansys Q3D
May 28, 2025 - Hi there! This video shows how Ansys Q3D Extractor can be used to compute capacitance values, starting with a basic parallel plate capacitor and then moving to a cutout from a MEMS...
>
Particle Deposition using the DPM
May 27, 2025 - In this video learn how to setup a model in Ansys Fluent to obtain results of particle deposition when using the Discrete Phase Model.
>
Dynamic Mesh Motion in Ansys Fluent— Part 3
May 26, 2025 - This is the third part of a video series on dynamic mesh motion in Fluent for CFD simulation. It features examples of vertical, horizontal, and general planar mesh motion.
The Flu...
>
Dynamic Mesh Motion in Ansys Fluent - Part 2
May 24, 2025 - This is the second part of a video series about dynamic mesh motion in Fluent for CFD simulation. It provides a step-by-step demonstration of implementing dynamic mesh motion for a...
>
Dynamic Mesh Motion in Ansys Fluent - Part 1
May 23, 2025 - This video provides a detailed explanation of the steps for dynamic mesh motion in Fluent, including examples of moving mesh using layering, smoothing, and remeshing techniques.
...
>
Transfer Chute Analysis
May 22, 2025 - A transfer chute is a crucial component in bulk material handling systems, commonly used in the mining industry to guide and control the flow of materials between different conveyo...
>
Modeling Wear in Ansys Rocky
May 22, 2025 - Learn how to set up and run a simulation that shows surface wear effects, visualize the resulting modifications, include particle trajectories, and analyze contact-derived properti...
>
Parallel Processing with Multiple CPU Cores in Ansys Fluent
May 22, 2025 - In this video, we demonstrate how to run a CFD model with Ansys Fluent using multiple CPU cores and evaluate the running time based on the number of CPU cores utilized for the simu...
>
Probabilistic Inference for Bayesian Optimization Application on a 2D Benchmark Case
May 16, 2025 - This video walks thorough the details of the Probabilistic Inference for Bayesian Optimization Application on a 2D Benchmark Case. The optimization tool is an embedded feature with...
>
Simulating a Conveyor Belt with Ansys Rocky
May 14, 2025 - This demo shows how to simulate a bucket conveyor system in Rocky DEM. We applied linear motion to the buckets, enabled periodicity, and calculated the timing for both straight and...
>
Using Mesh Regions in AEDT Icepak
May 14, 2025 - This video shows how to sdo one-click and advanced meshing on a simple electronics cooling problem using Ansys AEDT Icepak.
Please check out our blog: (https://blog.ozeninc.com/res...
>
Pressing and Thermoforming Simulation in Fluent Workspace Polyflow
May 13, 2025 - This video provides a setup of a pressing/thermoforming analysis in Ansys Fluent Polyflow. It showcases Polyflow’s capability to predict blow molded shapes.
Key highlights of...
>
Injection Blow Molding Simulation in Fluent Workspace Polyflow
May 13, 2025 - This video provides a setup of an injection blow molding analysis in Ansys Fluent Polyflow. It showcases Polyflow’s capability to predict blow molded shapes.
Key highlights o...
>
Stretch Blow Molding Simulation in Fluent Workspace Polyflow
May 13, 2025 - Stretch blow molding
This video provides a setup of a stretch blow molding analysis in Ansys Fluent Polyflow. It showcases Polyflow’s capability to predict blow molded shapes. ...
>
Modeling Electric Potential and Electrochemistry with Fluent
May 12, 2025 - This video shows how to setup battery cell and electrode model in Ansys Fluent. Here a micron level electrode/electrolyte model is considered where the potential equation and lith...
>
Thermal Analysis of High Power RF Coaxial Filter Using ANSYS AEDT (Two Way Coupling)
May 5, 2025 - Hi there! This video shows how to use the ANSYS Electronics Desktop (AEDT) to run a two-way coupled electro-thermal simulation of high power RF coaxial filter. ANSYS HFSS will be u...
>
Thermal Analysis of High Power Coaxial RF Filter Using ANSYS AEDT (One Way Coupling)
May 5, 2025 - Hi there! This video shows how to use the ANSYS Electronics Desktop (AEDT) to run electro-thermal simulation of high power RF coaxial filter. ANSYS HFSS will be used to perform the...
>
Generating Eye Diagram In ANSYS AEDT Using the HFSS 3D Layout & Circuit tools based on SIwave Solver
Apr 28, 2025 - Hi there! This video shows how to set up a serial channel on a PCB design using the HFSS 3D Layout tool in the ANSYS Electronics Desktop (AEDT). An eye diagram will be generated by...
>
Mastering Diffuse Scattering — Expert HUD Display Optimization with Ansys Solutions
Apr 28, 2025 - In this technical walkthrough, we demonstrate a complete diffuse scattering simulation workflow using Ansys Lumerical and Ansys Speos.
Starting with nanoscale surface roughness des...
>
Predicting Serial Channel Performance and Generating Eye Diagram In ANSYS AEDT Using SIwave Solver
Apr 24, 2025 - Hi there! This video shows how to set up a serial channel on a PCB model using the HFSS 3D Layout tool in the ANSYS Electronics Desktop (AEDT) . An eye diagram will be generated fr...
>
Battery Equivalent Circuit Model Simulation in Twin Builder
Apr 18, 2025 - This video provides a setup of a transient thermal analysis in Ansys Twin Builder. It showcases Twin Builder’s capability to quickly predict battery cell heat rejection from Hyb...
>
Ansys EMC Plus: One-Click Workflow for Simulating Shielding Effectiveness
Mar 28, 2025 - Hi there! In this video, we will explore one of the automated workflows of EMC Plus, which, with just one click, allows you to run a shielding effectiveness simulation.
Please che...
>
Boosting Photonics Simulation with Ansys Lumerical 2025 R1 | GPU Performance
Mar 27, 2025 - Explore the latest GPU performance enhancements in Ansys Lumerical 2025 R1, designed for simulation professionals, photonics engineers, and R&D leaders.
This video covers major up...
>
How Ansys Simulation Powers Advanced Automotive Camera Systems | Ozen Engineering
Mar 25, 2025 - Explore how Ansys tools—Speos, OpticStudio, and Lumerical—enable engineering teams to design and validate high-performance automotive camera systems for Advanced Driver Assista...
>
AR/VR Simulation Workflow EXPLAINED: From Optics to Thermal Stress
Mar 25, 2025 - Augmented Reality and Virtual Reality are transforming industries — from immersive training to advanced medical systems. But creating these devices requires a sophisticated simul...
>
Ansys Charge Plus: Paschen Test Demo
Mar 19, 2025 - Hi there! This video demonstrates the ESD simulation workflow in Ansys Charge Plus by simulating a parallel plate capacitor.
At Ozen Engineering Inc. (www.OzenInc.com) we help eng...
>
Antenna Matching using ANSYS Smith Chart Tool
Mar 14, 2025 - Hi there! This video shows how to use the ANSYS circuit smith tool to match an antenna designed and simulated with HFSS 3D. ANSYS HFSS designs can be dynamically linked into ANSYS ...
>
Estimating the transient response of an electronic assembly- Ansys Icepak
Mar 13, 2025 - This video showcases the setup of a transient thermal analysis in in Ansys Icepak. It showcases Icepak's capability in postprocessing transient results and generate solution datase...
>
Planar Patch Antenna Design Using ANSYS HFSS 3D Layout
Mar 12, 2025 - Hi there! This video provides an overview of the planar antenna simulation work flow in ANSYS HFSS 3D Layout with an illustration of how to design and simulate a planar slot-fed pa...
>
Busbar Induction Analysis with ANSYS Q3D Extractor
Mar 7, 2025 - Learn how to analyze power distribution busbars using ANSYS Q3D Extractor in this comprehensive tutorial. This video walks you through the entire process from initial setup to inte...
>
Building a Robust Metamodel for Electric Motor Optimization
Feb 27, 2025 - In this video, we continue our series on optimizing electric motors using MotorCAD and OptiSLang by examining our sensitivity analysis results and building a high-quality metamodel...
>
Integrated Simulations for Switched-Mode Power Converter EMI/EMC
Feb 25, 2025 - Hi there! This presentation from OzenCon 2025 provides an overview of Ansys Electronics solutions for EMI/EMC simulation and an example workflow to simulate conducted and radiated ...
>
Fluent Equivalent Circuit Model Applied to Steady-State Battery Module
Feb 20, 2025 - This video provides a demonstration of an Ansys Fluent CFD simulation of battery module using the Circuit Network – Equivalent Circuit Model. It includes a review of settings in...
>
New Structural Features in Discovery 2025R1
Feb 15, 2025 - ? Exciting news for engineers and designers! Discovery 2025R1 is here with groundbreaking features in structural analysis. From enhanced simulation accuracy to real-time feedback, ...
>
Wireless Power Transfer and SAR Simulation of Implantable Medical Devices Using Ansys HFSS
Feb 13, 2025 - Hi there! This video provides an overview of wireless power transfer and SAR simulation of implantable medical devices using Ansys HFSS.
At Ozen Engineering Inc. (https://hubs.ly/...
>
Battery Thermal Abuse Runaway Propagation Simulation Using Ansys Fluent
Feb 1, 2025 - This video provides a demonstration of how an Ansys Fluent CFD simulation of battery thermal abuse runaway propagation is set up for both a single battery cell and for a module of ...
>
Axial Flux Motor Design using Ansys MotorCAD
Jan 29, 2025 - Ansys MotorCAD Axial is a powerful new feature that enables engineers to design and optimize Axial flux electric motors with ease. Engineers will have full control and will be capa...
>
Setting Up and Running Sensitivity Analysis in optiSLang for BPM Optimization
Jan 27, 2025 - In this video, we complete the process of configuring a sensitivity study in optiSLang for optimizing motor designs.
Learn how to:
Adjust Motor-CAD parallel instances for ef...
>
Understanding Sensitivity Analysis and Sampling Methods in optiSLang
Jan 27, 2025 - Explore how sensitivity analysis and sampling methods in optiSLang help optimize designs by identifying critical variables.
Learn about the core sampling strategies, including Un...
>
Radio Frequency (RF) Amplifier Thermal Analysis with AEDT Icepak: Part 2
Jan 25, 2025 - In this video, we will work on a thermal simulation of a radio frequency amplifier. We will build our model using only AEDT Icepak and will not rely on an existing CAD definition. ...
>
Radio Frequency (RF) Amplifier Thermal Analysis with AEDT Icepak: Part 1
Jan 24, 2025 - In this video, we will work on a thermal simulation of a radio frequency amplifier. We will build our model using only AEDT Icepak and will not rely on an existing CAD definition. ...
>
FOC modeling with Space Vector PWM using Simplorer
Jan 20, 2025 - Field-Oriented Control (FOC) is a technique used to control AC motors by managing their torque and magnetic flux separately. This is done by converting the motor’s currents into ...
>
Radio Frequency (RF) Amplifier Thermal Analysis with Ansys Icepak: Part 2
Jan 18, 2025 - Almost all failure mechanisms in electronics are enhanced at higher temperatures. Therefore, accurate thermal modeling of electronics components are critical to the design process....
>
Radio Frequency (RF) Amplifier Thermal Analysis with Ansys Icepak: Part 1
Jan 18, 2025 - Almost all failure mechanisms in electronics are enhanced at higher temperatures. Therefore, accurate thermal modeling of electronics components are critical to the design process....
>
Integrating Motor CAD with optiSLang for IPM Motor Optimization
Jan 8, 2025 - Welcome back to our IPM motor optimization series!
In this video, we’ll walk you through the process of integrating Motor-CAD with optiSLang, a crucial step for automating sensi...
>
Setting Up an IPM Motor Model in Motor-CAD for Optimization
Jan 8, 2025 - Welcome back to our BPM motor optimization series! In this video, we take the first step by setting up a Brushless Permanent Magnet (BPM) motor model in Motor-CAD.
Watch as we mo...
>
Optimizing an IPM Motor with Motor-CAD & optiSLang: Full Overview
Jan 8, 2025 - Welcome to Ozen Engineering’s tutorial series on optimizing an Interior Permanent Magnet (IPM) motor using Ansys Motor-CAD and optiSLang.
In this video, we introduce the comp...
>
Phased Antenna Array Simulation Approaches in ANSYS HFSS
Jan 8, 2025 - Hi there! This video illustrates the different approaches that can be used to efficiently simulate phased antenna array using ANSYS HFSS.
At Ozen Engineering Inc. (https://www.Ozen...
>
AEDT Icepak and Electronics Cooling Analysis : Part2
Jan 4, 2025 - This video demonstrates how to step up an electronics cooling model in AEDT Icepak with step-by-step instructions. In part one of this vlog, building the model and creation of the...
>
AEDT Icepak and Electronics Cooling Analysis : Part1
Jan 4, 2025 - This video demonstrates how to step up an electronics cooling model in AEDT Icepak with step-by-step instructions. In part two of this vlog, meshing, running and posting the resul...
>
Importing External Electromagnetic Near Field Data into ANSYS HFSS
Jan 3, 2025 - Hi there! This video illustrates how to import electromagnetic near fields data into ANSYS HFSS.
At Ozen Engineering Inc. (https://www.OzenInc.com) we help engineers learn how to u...
>
Antenna Simulation Using Ansys Discovery
Dec 28, 2024 - Hi there! This video shows how to simulate a patch antenna in Ansys Discovery.
At Ozen Engineering Inc. (https://www.OzenInc.com) we help engineers learn how to use Ansys products...
>
Simulation of a High-Pressure Grinding Roll
Dec 24, 2024 - A High-Pressure Grinding Roll (HPGR) is a type of grinding equipment used in the mining and mineral processing industries. Its purpose is to crush and grind materials, typically or...
>
Particle Breakage simulation using DEM
Dec 24, 2024 - Title:
Accurate Particle Breakage Simulation is crucial in many industries such as mining, pharmaceuticals, construction, and food processing. The ability to simulate particle br...
>
The Benefits of Using CFturbo for Turbomachinery Design
Dec 20, 2024 - The video unleashes the power of advanced turbomachinery design with CFturbo. with a hands-on demonstration.
>
Importing Multiple Touchstone Files into ANSYS Electronics Desktop
Dec 18, 2024 - Hi there! This video shows how to import a list of N-port touchstones files into ANSYS circuit and HFSS 3D Layout tools. Instead of referencing a single files, an N-port model can ...
>
ANSYS EMC Plus Antenna in a Resonant Cavity
Dec 13, 2024 - Hi there! This video illustrates how the ANSYS EMA3D and MHARNESS simulation tools can be used to simulate the electric filed produced by an antenna inside a cavity.
At Ozen Engin...
>
Zemax STAR Module Tips for Engineers
Dec 7, 2024 - Discover the critical role structural and thermal modeling plays in high-power laser system design! ? In this video, we explore how Zemax OpticStudio, with its powerful STAR Module...
>
Importance of structural and thermal modeling in high-power lasers (Part1)
Dec 7, 2024 - Discover the critical role structural and thermal modeling plays in high-power laser system design! ? In this video, we explore how Zemax OpticStudio, with its powerful STAR Module...
>
Coaxial Cavity BP Filter Design Using Synmatrix and HFSS Integrated Workflow
Nov 25, 2024 - This video provides a brief introduction to SynMatrix. With SynMatrix and HFSS, users are able to design a wide variety of cavity filters. A caxial cavity BPF is discussed in this ...
>
Aerodynamic Analysis of a Sport Car with Ansys Discovery
Nov 23, 2024 - This video shows how to use Ansys Discovery to simulate the aerodynamic flow of air around a sports car. Setting up the model and physics in Discovery and tracking the force, press...
>
Mesh Adaption in Ansys Fluent - Part 2: Geometry-Based Adaption
Nov 21, 2024 - In Part 2, the video explains the steps for implementing geometry-based adaptation alongside other mesh adaptations for boundary layer and pressure gradient and how it matches the ...
>
Mesh Adaption in Ansys Fluent - Part 1
Nov 21, 2024 - In Part 1, you will observe the model setup and the application of mesh adaptation based on wall boundary layers and pressure gradient. It will demonstrate how these adaptations fu...
>
Ansys Discovery Room Ventilation Simulation
Nov 20, 2024 - The video demonstrates how effortlessly a classroom model can be created, set up, and its air distribution simulated using Ansys Discovery.
>
Modeling Phase Change During Adiabatic Expansion with ANSYS CFD Simulation
Nov 9, 2024 - In this video, we explain the setup for the phase change of water during adiabatic expansion and how to verify the results for condensation.
Ozen Engineering Inc. leverages its ...
>
CFD Analysis of Cooling in Adiabatic Expansion
Nov 6, 2024 - This video demonstrates the process of creating a CFD model that analyzes the cooling effects of adiabatic expansion. It also explores how the size of the opening influences these ...
>
Fiber Core and Clad Modeling with Mixed Mode in Zemax
Oct 30, 2024 - This video describes modeling core and cladding of optical fibers, the two main components that enable light transmission through Zemax.
>
LiDAR Simulation Guide: Using ANSYS SPEOS for Best Results
Oct 16, 2024 - In this comprehensive LiDAR simulation tutorial, I walk you through setting up a rotating LiDAR system using ANSYS SPEOS 2024 R2. From defining geometry, sensor sources, and materi...
>
Simulating Light from Free Space to Nano-Scale: Dynamic Link Between Zemax & Lumerical-Part1
Oct 12, 2024 - In this video, I explore the dynamic integration between Zemax (ray optics) and Lumerical (wave optics) to simulate light propagation from free space to the nano-scale. This powerf...
>
Electrodynamic Force Calculation on Bus Bars using Maxwell
Oct 11, 2024 - Three-phase short circuit events are critical in electrical systems where an unintended connection between three phases leads to a significant surge of current. These events can ca...
>
Model Building Part 2 ECAD import NC Meshing - Ansys Icepak
Oct 10, 2024 - This video showcases the powerful Non-Conformal Meshing feature in Ansys Icepak, a game-changing capability that revolutionizes thermal simulation for electronic systems. Non-confo...
>
Model Building Part 2 ECAD import - Ansys Icepak
Oct 4, 2024 - Ansys Icepak’s ECAD import simplifies thermal analysis by allowing seamless integration of electronic designs directly from ECAD tools. It enables the import of PCB layouts and c...
>
ANSYS HFSS: Array Analysis Using The Array Factor Calculation
Oct 3, 2024 - Hi there! This video shows how to use the ANSYS HFSS built in array factor calculation method to compute antenna array radiation pattern for designs that have analyzed a single arr...
>
Description of laser propagation with ZBF file in Zemax
Sep 24, 2024 -
>
Vibrating Screen Simulation, Part I: Efficiency
Sep 19, 2024 - In this video, you’ll learn how to set up the model and calculate screen efficiency over time. Follow the procedure for your own geometry and operating conditions. In this demo, ...
>
Vibrating Screen Simulation, Part II: Optimization
Sep 19, 2024 - Building on the setup shown in the first video, OptiSLang is used to run the optimization with two input parameters. The screen efficiency is maximized, reaching 98%—a 31% improv...
>
MotorCAD: Skin and Proximity Effect losses in Stator Windings
Sep 13, 2024 - MotorCAD is capable of accurately solving full FEA AC conductor losses, considering the placement of the conductor within the slot. Both single-slot and multi-slot calculations are...
>
Ansys Maxwell: Core and Magnet Losses in Electric Motors
Sep 11, 2024 - Eddy current losses in magnets affect the efficiency and thermal performance of electric motors. They occur when alternating magnetic fields induce loops of electrical current with...
>
Dam Breakup Simulation Using Ansys Fluent
Sep 11, 2024 - The video walks through the details of VOF multiphase modeling starting from geometry generation with SpaceClaim, meshing, model and simulation setting, and finally post-processing...
>
Crash course: Induced voltage analysis using SIwave and AEDT Circuit.
Sep 2, 2024 - This short video shows how to do Induced voltage analysis for a PCB, for EMI susceptibility, in less than 2 minutes.
About Ozen Engineering:
Ozen Engineering is a leading pro...
>
Crash course: FarField analysis using SIwave and AEDT Circuit.
Sep 2, 2024 - This short video shows how to do FarField analysis for a power planes and RF lines in a PCB, for EMI compliance, in less than 2 minutes.
About Ozen Engineering:
Ozen Engineer...
>
Crash course: NearField analysis using SIwave.
Sep 2, 2024 - This short video shows how to do Nearfield analysis for a power planes and RF lines in a PCB, to debug EMI, in less than 2 minutes.
About Ozen Engineering:
Ozen Engineering i...
>
Crash course: Frequency sweep analysis using SIwave and AEDT Circuit.
Sep 2, 2024 - This short video shows how to do frequency sweep analysis for a power planes and RF lines in a PCB in less than 2 minutes.
About Ozen Engineering:
Ozen Engineering is a leadi...
>
Crash course: SIwizard analysis using SIwave and AEDT Circuit.
Sep 1, 2024 - This short video shows how to do SIwizard analysis of RF lines in a PCB in less than 2 minutes.
About Ozen Engineering:
Ozen Engineering is a leading provider of Ansys solut...
>
Crash course: TDR analysis using SIwave and AEDT Circuit
Sep 1, 2024 - This short video shows how to do TDR analysis of RF lines in a PCB in less than 2 minutes.
About Ozen Engineering:
Ozen Engineering is a leading provider of Ansys solutions,...
>
Crash course: Crosstalk scan using SIwave.
Sep 1, 2024 - This short video shows how to do Crosstalk scan of all the RF lines in a PCB in less than 2 minutes.
About Ozen Engineering:
Ozen Engineering is a leading provider of Ansys ...
>
Crash course: Resonant modes using SIwave.
Sep 1, 2024 - This short video shows how to do Resonant modes of all the powerplanes in a PCB in less than 2 minutes.
About Ozen Engineering:
Ozen Engineering is a leading provider of Ans...
>
Crash course: Zo scan using SIwave.
Sep 1, 2024 - This short video shows how to do Zo scan of all the RF lines in a PCB in less than 2 minutes.
About Ozen Engineering:
Ozen Engineering is a leading provider of Ansys solutio...
>
Flownex Video: Crude Oil Network in Flownex – Part 2
Aug 24, 2024 - Transient simulation in Flownex can be a valuable tool in oil pipeline simulation technology. It can be used to assess the impact of sudden changes in thermal crude oil boundary co...
>
Flownex Video: Crude Oil Network in Flownex – Part 1
Aug 24, 2024 - TThe oil and gas industry often utilizes pipeline simulation to simulate the movement of crude oil. To accurately predict the pipeline's flow rate, it's important to consider the t...
>
Aspherical Lens for Thin Laser Beam Uniformity
Aug 19, 2024 -
